Easy Temp is produced in Europe.

With remote monitoring, Easy Temp BLE simplifies temperature sensing and speed of operation, plus through the App it sends notifications when the temperature rises or falls, according to the set parameters.

Easy Temp NFC does not have a battery and this allows the device to activate only whenever temperature is to be taken from the patient, using an NFC reader, which through the App stores data about the patient.
Easy Temp NFC is suitable for patients who do not need short interval temperature monitoring.

For security reasons, you have to manually select each patient for a data safeguard.

Easy Temp, as per certifications, is considered a device that interacts with the body in a non-threatening manner, so they can be used on pregnant women as well.

Biomedical devices by regulation (as specified in the certifications) must be used within two years from the date of manufacture.

The device can be applied only in the areas indicated by the manual: between the axillary cord and the clavicular bundle, on both sides.

The waiting time is 5 minutes from the application of Easy Temp.

Easy Temp adhesive has a shelf life of 3 consecutive days from the first application.

Once Easy Temp is removed from the skin, the adhesive must be removed by pulling the red tab on one of the corners.
The new sticker should be applied to the Easy Temp device in the direction indicated by the protective label marked “sensor,” and then it should be placed on the patient by removing the “skin” protection.

The Easy Temp device can be washed without damage with soap and water. Alternatively, ultraviolet autoclaving can be used in order to make the device sterile.

You have to gently lift the adhesive that is in contact with the skin, and remove it from it. See the manual.

No, you have to replace the adhesive and sanitize Easy Temp every time you want to apply it to a different patient.

Easy Temp is capable of measuring temperature and transmitting it through the BLE interface to any device with a BLE connection by installing a special application provided.

No, it should be removed previously and reapplied when used again after X-ray examination.

As for Easy Temp NFC, monitoring is done directly through the App, which once enabled automatically detects the temperature by bringing the NFC reader close to the patch, and the data is saved within the server, available later in the cloud. See the manual.

The app is available for all Apple devices with iOS 12.0 or later, and all Android devices from version 5.0 of the operating system. As for Apple devices, use of the NFC-enabled temperature measurement feature is available for iPhone 7 and later devices.
However, it is possible to view the history of NFC measurements already taken regardless of the availability of NFC reading functionality.

Remote monitoring has a transmission capacity ranging from 8mt to 15mt.

No, it can be associated with one Easy Link device at a time.

Yes, up to 4 Easy Temp BLE devices can be paired with an ET-Link router.

Yes, because Easy Temp NFC devices do not require a router, temperature monitoring is done directly through the App by bringing the NFC reader close to the device.

You have to associate the device with the patient and then with Easy Link before you can use it. In the case of Easy Temp NFC devices, you just need to configure it to the App, entering patch serial and patient.

This is only possible for Easy Temp BLE devices. The App remains active at all times in order to send any notifications, even in the background.

No, because measurements via NFC take place directly in the presence of the patient.

If the NFC reading operation fails, it may be sufficient to move the smartphone away from the device and back again, or align it with the device in a different way, as the position of the NFC sensor on the smartphone may be different depending on the model.
In the event that the reading fails after repeated attempts, even using different smartphones, the Easy Temp device may be defective and therefore will need to be replaced. See the manual.

Simply configure Easy Temp the first time you log in, without having to repeat the process each time you monitor.

The router must be enabled to a facility Wi-Fi network with Internet access. The configuration procedure is explained in detail within the manual. See the manual.

In case of weak or absent BLE signal, the Easy Temp keeps all detected measurements in memory.

If the router is unplugged from the power outlet, Easy Temp keeps in memory all the measurements taken, as for weak signal cases. Once reconnected, the router resumes its normal activity without the need for any user intervention. In case the Internet connection is lost for a short time, the data received from Easy Temp patches are automatically saved and sent once the connection becomes available again. See the manual.

When the blue LED indicator is off, there are no associated Easy Temp devices and the BLE module is inactive.

If its blinking is slow, it means it is scanning for new Easy Temp devices; if its blinking is fast, it is searching for existing Easy Temp devices to receive data.

It means that the Easy Link device is connected to an Easy Temp device.

It means that the router is not connected to any Wi-Fi network.

It indicates that the Easy Link device is in Access Point mode.

It means that the router is connected to a Wi-Fi network.

At power-up, if there are no EasyTemp devices associated, the router will wait for the search command via button, otherwise it will start searching for already associated devices and receive data from them.
The search command for new devices will allow a new EasyTemp patch to be associated within the next 30 seconds, after which the router will return to its previous operating mode.

To change the temperature thresholds, open the patient screen by tapping the button with his or her initials, and use the slider in the “Temperature Thresholds” field to set the new values.
Then confirm the new settings by tapping the button with the check mark in the upper right corner. From now on, you will receive notifications once the new thresholds set are exceeded.

Yes, but it should be removed from the patient in case of prolonged contact with water, as like any electrical device, this could alter its functionality.

For optimal operation, 55°C should not be exceeded.

Absolutely not.

No, it must be purchased separately.

No, it cannot be cut in any way.

No, do not expose the device to electromagnetic fields except those produced by mobile phones/tablets with which the device must work.

In case the user has unintentionally turned on the device, it will turn off within 30 seconds if it is not associated with his Easy Link Router.

Easy Temp BLE is made of a material that makes it flexible, yet durable. If such a situation should happen, it is advisable to replace the device with a new one, for the sake of the safety of the people using it.

No, upon removal it leaves no adhesive residue on the skin.

No, the measurement is in both Celsius and Fahrenheit.

Yes, as with any temperature control device, the values if at very close intervals can have a minimal margin of difference (accuracy range ± 0.1°C).

Easy Temp BLE stores approximately 250 measurement values, this is equivalent to 10 days if the temperature monitoring interval is every 60 minutes. If the memory is full, the last value taken remains stored.

Open the patient’s screen by tapping the button with his or her initials, then open the drop-down menu in the “Sampling Time” field, and select the new value.
Then confirm the new settings by tapping the button with the check mark in the upper right corner.

Should it occur, through Easy Temp Bluetooth a temperature below the set threshold will be detected(given the lack of contact with body heat), following will be notified through the App, as a wake-up call and incitement to control by the doctor.

The data collected by the Easy Temp device is transmitted via BLE to the ET-Link router and then sent to the server for viewing via the App or the appropriate web interface.

Temperatures associated with the patient are saved within the server and can be viewed through the App or the appropriate web interface.

Easy Temp must first be disabled before it can be configured again and applied to a new patient. If this process is not performed correctly, it will be notified by the system, which will prompt the User to proceed in the correct manner. See the manual.

Battery life varies depending on the measurement interval chosen. It can range from 2 days (for a 2-minute interval) to 30 days (for a 30-minute interval).

You need to stop using Easy Temp BLE, and replace it with a new device.

Through the smartphone App, it is also possible to keep an eye on the remaining battery level.

No, because it is powered through NFC technology.

Yes, as Easy Temp is considered a medical device in its own right.

Easy Temp has high hypoallergenic characteristics with high skin tolerability, but should it cause any reaction, allergic or redness in the area of application, it should be removed promptly.

No, as per CE Certification according to 93/42/EEC Class II (amended by Directive 2007/47/EC et seq., Class II -a), validated for ISO13485, Easy Temp guarantees the safety of the patient and the professionals who use it.

No, because being a certified medical device and not containing any kind of medication inside, it has no contraindications.

Easy Temp falls into the WEEE R4 waste category, as it consists of electrical components, and in Italy it finds its reference in Legislative Decree No. 49 of March 14, 2014, issued in implementation of the European Directive 2012/19/EU, which requires that specific companies be approached to dispose of them once their functionality is exhausted.